All About Denim Wash

Denim Washing

Denim washing is an aesthetic finish that is imparted to improve the softness and comfort of the fabric. In addition, the fabric achieves a different look such as a faded or worn-out appearance. It also enhances the appeal and to provide strength. The emphasis is on comfort and softness.

 Washing has such an important part in the denim chain because of the umpteen effects that consumers look for in their jean

Denim Wash - Thread Recommendations & Washes Process for Jeans ...

Types of Denim Washing

Denim washing are two types. These are

1. Mechanical washes

  • Stone wash
  • Micro sanding

2. Chemical washes

  • Denim bleaching
  • Enzyme wash
  • Acid wash

Some Important Steps in the Process of Denim Washing:

For Wet Process

  1. Pre treatment ( Desizing, Rinsing, Scouring etc)
  2. Enzyme or Stone wash
  3. Clean up to adjust the desire effect
  4. Bleaching
  5. Tinting / Dyeing
  6. Softening & Much more….

For Dry Process

  1. Whiskering
  2. Laser Whiskering
  3. sandblasting
  4. Laser treatment
  5. Hand Scraping
  6. Grinding
  7. Overall Crinkle
  8. 3D Crinkle

Machines / Apparatus used in Denim Dry process :

  1. Abrasive paper
  2. Hand Scraping machine
  3. Whiskering pattern
  4. Grinding machine
  5. Destroying machine
  6. 3D Crinkle machine
  7. Normal Crinkle machine
  8. Pen grinding machine
  9. Tagging machine
  10. Oven dryer
  11. Heat setting machine
  12. Conveyer oven
  13. P. Spray Cabin
  14. Sprayer
  15. Laser machine
  16. Ozone washing machine
  17. Crown heat gun
  18. Air dummy – horizontal
  19. Air dummy – vertical
  20. Tie ( Net, Socks , Rope , Cable etc. )
  21. Chalk
  22. Pensil
  23. Rotating Brush
  24. Quality table with light box etc.

 Different dry processes

1 . Whiskering : Whiskering is the first process and one of the most important process in denim dry process. Different whiskering pattern is developed according to the design and the garment is scrabbed over the prepared pattern with abrasive paper or emery paper to get the whiskered effect or fading effect.

Whisker can be made in different ways. But the top most ways are as follows.

  1. By whiskering pattern
  2. By Manual hand scrap.
  3. By using laser Machine.
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

A . By whiskering pattern :  Different process can be used to make whiskering pattern . One process is given below :

  1. At first the design is selected then a white poly is placed on the the garment.
  2. Marking the design with marker with seam line
  3. Taking a rubber board and replace the marked poly on the rubber board
  4. Engaving the marked rubber board area of whiskering by cutter or blade
  5. Whiskering pattern is made
  6. The pattern then inserted into the denim garments
  7. Scrape over the engraved area and the whiskered design is created.
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

After making the whiskering pattern , the board is placed inside the denim garments and the emery paper or abrasive paper is scrabbed over the engraved pattern.

B . Manual Hand Scraping : Manual process is also used to bring the whiskering pattern design on the denim garments. Apparatus is used for hand scraping is given below :

  1. Pattern
  2. Emeri paper or abrasive paper
  3. Chalk powder
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

Abrasive paper grading :

  1. P – 400 ( very rough surface for hard fabric )
  2. P – 800 ( medium rough surface for medium hard fabric )
  3. P – 1000 ( less rough surface for soft fabric )

As the number increases the power of abrasive paper decreases.

  Manual hand scraping process is given below  :

  1. First the design is observed then draw the design with a chalk on the denim garments carefully
  2. Scrape on the drawn line of the design by the abrasive paper thus the design is created.
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

C . Using Laser Machine : Laser machine is used to make whiskering or burning effect on the denim garments. This process is done after the washing process. Different intensity of light is used to get the desired design. Laser is produced by the combination of co2 and DC current.

  The process is given below :

  1. First, the whiskering design is made by photoshop or illustrator
  2. Design is transferred to laser machine
  3. The intensity of laser light is selected
  4. Laser light is imposed on the denim garments to get the design
  5. After the wash the burned indigo is removed and the whisker is visible
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

Operating flow path of Easy mark supervisor software is given below :

Open —> Import image —> Open file for insert diagram —> Image Size —> Selection —> Tools —> Pointer Online —> Pointer Online off —> Print.

Configure —> Advance Configure —> Enable Automatic Selection —> Ok.

Configure —> Massage Table —> Add (front right, back right, front back right) —> After Adding OK —> Print.

2 . Hand Scraping / Sanding : This dry process is applied after whiskering to remove the color or fade specific area of the garments and become very important now a days. Abrasive paper , Air dummy ( horizontal ) , gum tape and Hand is used . This process is more used as sand blasting process is banned due to hazadous to health.Hand scraping process is given below :

  1. First the garments is mounted on the air dummy and fitted into two M.S. pipe
  2. Both end of each pipe covered with rubber tube and tightened by suitable clamping
  3. After inserting the garments then the dummy is filled with compressed air as per required pressure
  4. While scraping with hand , Pressure should be uniform
  5. Then sent to washing to get the desired efffect

3 . Grinding : Grinding is the destruction of edges or the worn out effect on the edge of the garments. If the garments has two time wash that time we will wash it after first wash to avoid the damages of garments. It is often done on hem, pocket edge, west belt , pocket opening and pocket pluf of the garments. It brings old look appearance and creates high fashion garments. Grinding machine is used to destroy the edges . For grinding small size stones are used in the grinding machine.

Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

4 . Destroy : Destroy is the most popular distressing method which is done by pen grinding machine with different size stones. It look like holes and worn out white yarns which make garments unique and fashionable.

   Different types of apparatus and requirements :

  1. Grinding machine
  2. Grinding wheel
  3. Different size stones
  4. Niddle
  5. Knife
  6. Electricity
  7. Safety accessories

  Destroy process by grinding machine :

  1. First mark the place to be destroyed by the grinding machine
  2. Slightly attach the machine with the garment and slowly remove the cellulose
  3. After washing it will get the desired effect
Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

  Destroy process by niddle and knife :

  1. This is manually done by cutting the warp yarn or making holes by knife
  2. Having 3-5 small holes are enough but too many holes are not preffered
  3. Keeping the weft yarn to show the white thread
  4. Knife is run along the warp direction 10 times or more in a certain area
  5. The area around the destruction done is worn out
  6. After wash it will show the desired effect

After the destroying process the white yarn losses strength and to strengthen those yarns acetic si-sealant could be used which may prevent the breakout and tearing of those yarns.

Or , To reinforce the newly created holes , turn the garment inside out and place and adequate patch  or cut piece of fabric around it and sew it

Safety measurements are taken during the destroy process by wearing masks and gloves.

Denim Dry Processes - Whiskering , Laser Whiskering , Hand Scraping, Grinding, Destroy | Machines / Apparatus used in Denim Dry process | whiskering  By pattern| Manual hand scraping | Whiskering  By laser Machine | Textile Study Center |

5. Overall Crinkle : The full garments is washed with resin and after hydro-extacting the full garments is dryed then special effect is produced. For the effect , the garment is tied with thread or net or rope which resin treatment. Overall crinkle is done the all types of fabrics like denim  , twill , canvas , poplin , knit , viscose , nylon etc. This is done after all types of dry and wet process. This is very popular and widely used in denims now a days.

  Resin solution prepared :

  1. Resin 20%
  2. Water 80%

  Machine / Apparatus / Requirements for overall crinkle process :

  1. Washing machine
  2. Trolley
  3. Hydroextractor
  4. Curing machine
  5. Tie , rope , thread

  Overall Crinkle process is given below :

  1. Garments are tied with rope, tie , thread
  2. Then, garments are loaded into the washing machine with solution
  3. Let, temparature is 50 oc and keep the machine running for 10-15 minutes.
  4. Then , unload the garments from washing machine to trolley and start hydroextracting
  5. Untie or cut the threads, ropes
  6. Put those garments into curing machine and set the machine at 140- 160 oc for 40-60 minutes
  7. When the time exceeds , machine automatically becomes off
  8. Then , all the garments are hanged by hanger for 10-15 minutes for cooling

After those processes the garments are checked for quality and delivered.

6 . 3D Crinkle :  It is one of the important finishing treatment on denim garment which is applied after wet process. Bringing 3D effect on denim garments by treating with resins are called 3D crinkle. This process is done manually or semi autometically using resins like low formaldihyde or DMDHEU type resins which make crosslinks between cellulosic bonds and when the fabric deforms or folds or losses its normal orientation , those chemicals prevents the transformation to normal position and that causes wrinkles or creases. Various supporting auxilliaries are used for better penetration of resins and softeners used for softness.

  Techniques  for 3D Crinkle finish :

  1. By 3D crinkle machine
  2. By Heat setting machine
  3. By Spray and chemical application cabinet with conveyer
  4. By 3D wire crinkle machine
  5. By 3D bendable leg or air dummy
  6. By using clip
  7. By garment crushing machine
  8. By tying garments with air

  Solution :

  1. Water
  2. Resin
  3. Supporting auxilliaries

  Control parameters :

  1. Temparature
  2. Time
  3. Concentration of solution

The process of 3D crinkle is given below :

  By 3D crinkle machine :

  1. The machine consist of 6 heads and changeable leg distance .
  2. Both legs can work simultanously.
  3. It requires no chemicals for crinkle effect on denim.
3D crinkle machine

  By Heat setting machine :

  1. This machine give permanent creases
  2. First , spraying resins on specific area of the garments
  3. Then , pressing with heat bring permanent crease in the garments.

  By Spray and chemical application cabinet with conveyer :

  1. First , the resin solution is sprayed on the garments where needed
  2. Then , cliping the area to get desired effect
  3. Sending those garment into the chemical application cabinet
  4. This cabinet has specific temparature for curing , normally 140-160 oc
  5. A converyer belt moves all the garments to the initial position to final position
  6. Time is given when it is needed to be off
  7. This machine operates automatically after giving instruction

  By 3D wire crinkle machine:

  1. There are 3 operation heads and 3 stations.
  2. The operation time is around 30 seconds.
  3. 1 person can control and work with this machine.
  4. Desired effect can be easily and quickly made by this sytem

  By 3D bendable leg :

  1. This machine consist 1 head and 1 hanger
  2. It brings crinkle effect only using air
  3. It gives natural crinkle effect on denim

  By using clip :

  1. First , resin is sprayed on garments
  2. Then, the area is folded or creased by clip
  3. Finally , the garment is sent to the oven for curing

  By garments Crushing machine :

  1. It a crushing machine of steam system which brings creases all over the garments
  2. Effects can be adjusted using steam , pressure level and chemical level

  By tying with thread :

  1. First , garments is soaked into resin solution
  2. Then , thread is used to bend or fold or pleat where effect is desired
  3. Finally , garments sent to oven for curing

  Precautions for 3D crinkle effect when resin is applied :

  1. If more resin is applied in a specific area , the garment may tear
  2. If resin applied more than one time , garment may tear
  3. If oven time is more , tear can occur
  4. If exposure time is more, tear may occur
  5. For more resins , garments can be so hard
  6. Unwanted spots can appear
  7. If more resin applied in pocket area ,then pocket may damage

General finishing sequence of denim:

There are almost countless variations of processing techniques used by designers and textile chemists to achieve fashionable looks that are distinctive and desirable. Only the basic treatment conditions are addressed in this chapter; the number of variations is very large and the evolution of chemical and mechanical techniques is continuing. There often are some secretive and proprietary methods. Regardless of the specific look and name chosen, the following are the process steps normally used to attain the desired results.

Flow Chart of Denim Finishing



Washing (abrasion)





In denim garments, preparation consists primarily of desizing, which enables subsequent chemical and mechanical treatments (washing/abrasion) by removing the previously applied warp size. Untreated denim garments are extremely rigid due to the size applied at the yarn stage for increasing weaving efficiency, by coating the yarn with a protective outer layer which retards yarn breakage. The sizing remains in the yarn after the fabric is woven and, therefore, provides fabric stiffness necessary for more efficient sewing of garments. Sizing is typically made up of starch (or polyvinyl alcohol/starch), binders and waxes and lubricants. Additionally, finishes containing starch and/or polyvinyl alcohol are applied to denim as a topical finish before the fabric is shipped to the sewing plant.

After desizing, denim garments are rinsed to remove all size materials before washing/ abrasion. Different washing/abrasion techniques are introduced in the following sections. Again after the washing/abrasion processes, denim garments are rinsed to remove unwanted materials from fabric surface. Then a softening process enhances the hand feel and softness of the denim garments. Finally the denim garments are dried and packed for delivery.

The most popular method of removing starch from denim garments is to use amylase enzyme. This product can break down the long starch molecular chains (water insoluble) into smaller molecules (water soluble) which can be more easily washed away. The removal of starch from the fabric being desized can also usually release some quantities of indigo into the bath. Therefore, a neutral pH nonionic surfactant is used for suspending loose dye in the water, to prevent redeposition onto the garments as well as to aid penetration of the desizing liquor into the interior of the fibres. It is also important to follow the desizing bath with a hot water rinse. Introduction of cold water onto the denim garments at this point can resolidify the fats and waxes, and tends to redeposit the gelatinous components unevenly on surface.

Rinse wash or Regular washing:
Rinse wash is the simplest type of industrial garment wash. The main aim is to remove starch, dust and dirt from garments. Sometimes reasons for a normal wash include softening and giving the garment a used look. For colour garments, removal of unfixed dyes can be achieved to improve colour fastness. In special cases, intentional shrinkage in garments can be achieved. Precautions need to be taken against unwanted shrinkage issue and back staining.

 Regular washing is the simplest and most commonly used washing method for denim garments. It is most basic wash for denim garments. Typically named a dark wash, the only purpose of this wash is to make the garment wearable. The degree of color fading using regular washing is comparatively slight, but it provides uniformity, depending on whether it is deeply dyed classic denim or only moderately dyed with poor penetration. Generally speaking, detergent is used for regular washing for about 15 min at temperatures between 60 °C and 90 °C. Softening is applied after the washing process. Regular washing can improve the softness and comfort properties of denim garments as well as enhance aesthetic property. Depending on the time and amount of chemicals used, regular washing can be classified into (1) light washing (washing time about 5 min); (2) normal washing (washing time about 15 min); and (3) heavy washing (washing time about 30 min). However, there is no significant distinction between light, normal and heavy regular washing as it depends on the actual washing conditions.

Flow chart of general regular washing process is as follows:
Wetting↓Desizing↓Regular washing↓Softening.
A sample recipe for a normal wash is:
If the lot size is 100 kg cotton shirts,

  • Material: liquor ratio (M: L ratio)
  • Water = 500 L
  • Detergent = 1% (based on the weight of the garments)
  • Temperature = 40–60°C
  • Time = 15–30 min

Back-staining chemical is used if required

Hydrogen peroxide wash or Bleach washing:
Hydrogen peroxide is rarely used as a bleaching agent only when very little loss of colour is required or if the fabric is coated with sulphur, because it takes longer to achieve the desired effect. Hydrogen peroxide has a prime role in the bleach wash technique. In an alkaline medium, hydrogen peroxide breaks up and gives off some perhydroxyl ions, which destroy the colouring matter and result in a fading effect. Hydrogen peroxide is used in a scouring, bleaching bath for white textile material or “ready for dyeing” form of garments made from grey fabrics. We have also published article on bleach wash of denim. You can read below.

You may also like: Denim Bleach Wash Process

Stone washing:
It is one of the most popular denim wash. It gives a newly manufactured denim garments a worn-out appearance. It also helps to increase the softness and flexibility of denim garments otherwise fabric keep stiff and rigid. We have published a comprehensive post on stone wash process of denim garments.

Enzyme washing:
Enzyme wash is a process that gives denim a softer and worn-in look by breaking down the cellulose molecules naturally found in indigo dyes. Denim washing with enzymes is one of the most widely accepted enzyme-based. Enzyme washing of denim with various benefits both economically and environmentally. You can see our complete article on enzyme wash on denim.

You may also like: Enzyme Wash | Denim Enzyme Wash Process

Acid, ice and snow wash:
This finish gives indigo jeans sharp contrasts. The process was created in Italy and was patented in 1986. Interestingly, acid wash denim does not use actual acid in the wash process. Instead the process uses pumice stones soaked in bleach to alter the colour in a nonuniform manner. The result is often splotchy yellowish patterns. This finish provides jeans with sharp contrasts in tonal colour. This is also known as ice or snow washing. This is achieved by dry tumbling with pumice stones soaked with bleaching agents to produce a ‘snow’ pattern effect on denim. Stones are used to deposit a chemical on garments to strip off the colour. This chemical deposit removes colour only from the outer surface of the garments and produces a frosted appearance. Indigo and selected sulphur dyes are the most popular candidates for this procedure.

Acid washing:
To change the look of denim or jeans different types of washing process are done. Among various washing process of denim, acid wash is the most popular. This is the oldest of fashion washes in denim after stone wash. You can see our exclusive article on acid washing process in denim jeans.


Leave a Reply

Your email address will not be published. Required fields are marked *

Battlefield 2042 Specialists & launch maps revealed By EA
Latest News

Battlefield 2042 Specialists & launch maps revealed By EA

After months of speculation, EA and DICE have finally unveiled Battlefield 2042, with the reveal trailer already live and a gameplay one set to premiere on Sunday, during Microsoft’s E3 conference. There may be additional information released at that point but for now we already know quite a bit about the new maps and the Specialists, 2042’s version of the […]

Read More
UK Travel Green List & Rules for entering
Latest News

UK Travel Green List & Rules for entering

Red list countries and territories What you must do if you have been in a country or territory on the red list in the 10 days before you arrive in England. If you have been in a country or territory on the red list in the last 10 days you will only be allowed to […]

Read More
Latest News

Belarus to face Slovakia in 2021 IIHF World Championship opener

Belarus will open the 2021 IIHF World Championship against Slovakia in Riga on 21 May, BelTA has learned. The Group B match will be played at the Olympic Sport Center. The faceoff is at 20.10. Belarus 5 TV channel will broadcast the match live. Ahead of the IIHF World Championship Belarus played a number of […]

Read More